Program Admission Notes:
To apply to ECU as a transfer student:
-
Complete, or have in progress, a minimum of 24 transferable college-level courses
-
Have a minimum 2.0 cumulative GPA for all college-level coursework attempted
To be admitted to the Engineering major, transfer students must have
-
a cumulative 3.0 or higher undergraduate GPA
-
a 2.8 or higher if Associate in Engineering degree is earned/completed
-
completed transferable credit for
-
ENGL 1100 (ENG 111)
-
ENGL 2201 (ENG 112)
-
CHEM 1150, 1151 (CHM 151)
-
MATH 2171 (MAT 271)
|
Contact:
College of Engineering & Technology
cetadvising@ecu.edu
Revised:
May, 2024
|
College Level Foreign Language Requirements:
There is no foreign language requirement for this major.
Major-Specific Course Recommendations:
Students are encouraged to build the Community College course recommendations below into the associate degree to best prepare for the intended major.
Recommended CC Course |
Credit Hours |
University Equivalent |
Associate Degree Requirement Fulfilled |
University Requirement Fulfilled |
ENG 111: Writing and Inquiry
|
3
|
ENGL 1100: Foundations of College Writing
|
English Composition
|
Required Course
|
ENG 112: Writing/Research in the Disc
|
3
|
ENGL 2201: Writing About the Disciplines
|
English Composition
|
Required Course
|
PHY 251: General Physics I
|
4
|
PHYS 2350: University Physics I
|
UGETC Natural Sciences
|
Required Course
|
PHY 252: General Physics II
|
4
|
PHYS 2360: University Physics II
|
UGETC Natural Sciences
|
Required Course
|
MAT 271: Calculus I
|
4
|
MATH 2171: Calculus I
|
Additional General Education Courses
|
Required Course
|
MAT 272: Calculus II
|
4
|
MATH 2172: Calculus II
|
Additional General Education Courses
|
Required Course
|
MAT 273: Calculus III
|
4
|
MATH 2173: Calculus III
|
Additional General Education Courses
|
Required Course
|
EGR 150: Intro to Engineering
|
2
|
ENGR 1000: Introduction to Engineering
|
Elective/Pre-Major Courses
|
Required Course
|
HEA 110: Personal Health/Wellness
|
3
|
HLTH 1000: Health in Modern Society
&
KINE 1000: Lifetime Phys Act and Fit Lab
|
Elective/Pre-Major Courses
|
Required Course
|
BIO 110: Principles of Biology
OR BIO 111: General Biology I
|
4
|
University Equivalencies
|
Elective/Pre-Major Courses
|
Required Course
|
CHM 151: General Chemistry I
|
4
|
CHEM 1150: General Chemistry I
&
CHEM 1151: General Chemistry I Lab
|
Elective/Pre-Major Courses
|
Required Course
|
Remaining Associate Degree Requirements:
In addition to major-specific course recommendations above, students should work with a community college advisor to select additional community college courses to fulfill the remaining associate degree requirements identified below.
Recommended CC Course |
Credit Hours |
University Equivalent |
Associate Degree Requirement Fulfilled |
University Requirement Fulfilled |
Student Choice/No Preference
(Approved Course Options)
|
6
|
University Equivalencies
|
UGETC Humanities/Fine Arts
|
General Education
|
Student Choice/No Preference
(Approved Course Options)
|
6
|
University Equivalencies
|
UGETC Social/Behavioral Sciences
|
General Education
|
MAT 171: Precalculus Algebra
|
4
|
MATH 1065: College Algebra
&
MATH 1XXX: Math for Liberal Arts
|
UGETC Math
|
General Education
|
MAT 172: Precalculus Trigonometry
|
4
|
MATH 1083: Precalculus
&
MATH 1XXX: Math for Liberal Arts
|
UGETC Math
|
General Education
|
ACA 122: College Transfer Success
|
1
|
COAD 1XXX: Univ Studies for Early College
|
Academic Transition
|
Elective
|
Student Choice/No Preference
(Approved Course Options)
|
1
|
University Equivalencies
|
Elective/Pre-Major Courses
|
Elective
|
Remaining Bachelor’s Degree Requirements at University:
University Course |
Credit Hours |
University Course Notes |
ENGR 1012: Engineering Graphics
|
2 |
|
ENGR 1016: Intro to Engineering Design
|
2 |
|
ENGR 2000: Engr Design and Proj Mgmt I
|
1 |
|
ENGR 2001: Linear Algebra Laboratory
|
1 |
|
ENGR 2022: Statics
|
3 |
|
ENGR 2050: Intro to Engr Computation
|
3 |
|
ENGR 2070: Materials and Processes
|
3 |
|
ENGR 2450: Dynamics
|
3 |
|
ENGR 2514: Circuit Analysis
|
4 |
|
ENGR 3000: Engr Design and Proj Mgmt II
|
2 |
|
ENGR 3024: Mechanics of Materials
|
3 |
WI |